Guide
What chemicals do I need to close a pool, and how much?
Winter closing doses by pool size: liquid chlorine to shock level, muriatic acid for pH, baking soda, stabilizer and salt, all computed from the app's chemistry engine. Algaecide stays on the label.
Updated · 5 min read
Use liquid chlorine to shock level, muriatic acid for pH, baking soda for TA, stabilizer for CYA, salt if low. Per 10,000 gallons: 12.8 fl oz of 10% liquid chlorine per 1 ppm of FC, 8.0 fl oz of muriatic acid from 7.8 to 7.5 at TA 80, and 267.8 lb of salt to reach 3,200 ppm from zero.
Measure against your test results, not the calendar: dose what your water needs, nothing more. Every number in the tables below is what the app's water check computes; enter your readings there and it scales them to your exact volume.
Chlorine to shock level
At closing you raise free chlorine to shock level, which depends on CYA. At CYA 40, shock level is 16 ppm. The table shows the dose per 1 ppm of free chlorine, so multiply by the rise you need. From FC 3 to 16 ppm in a 15,000-gallon pool is about 249.4 fl oz, or 2 gal, of 10% liquid chlorine.
Shock level for your CYA, with the mustard-algae rate beside it:
| CYA | Shock level (ppm) | Mustard algae (ppm) |
|---|---|---|
| 20 or less | 10 | 12 |
| 30 | 12 | 18 |
| 40 | 16 | 24 |
| 50 | 20 | 30 |
| 60 | 24 | 36 |
| Pool size | 10% liquid chlorine per 1 ppm | 12.5% liquid chlorine per 1 ppm |
|---|---|---|
| 10,000 gal (38,000 L) | 12.8 fl oz | 10.2 fl oz |
| 15,000 gal (57,000 L) | 19.2 fl oz | 15.3 fl oz |
| 20,000 gal (76,000 L) | 25.6 fl oz | 20.5 fl oz |
| 25,000 gal (95,000 L) | 32.0 fl oz | 25.6 fl oz |
Metric, per 10,000 liters: 100 mL of 10% or 80 mL of 12.5% raises free chlorine by 1 ppm.
Acid to lower pH
Closing balance usually means nudging pH down one last time. Doses of 31.45% muriatic acid for a pH drop from 7.8 to 7.5 at TA 80:
| Pool size | Muriatic acid | Metric |
|---|---|---|
| 10,000 gal | 8.0 fl oz | 235 mL |
| 15,000 gal | 11.9 fl oz | 353 mL |
| 20,000 gal | 15.9 fl oz | 470 mL |
| 25,000 gal | 19.9 fl oz | 588 mL |
Higher TA needs more acid for the same change, and weaker acid takes proportionally more. The water check gives the dose for your pH, TA and acid strength.
Baking soda to raise alkalinity
Per 10 ppm of total alkalinity:
| Pool size | Baking soda | Metric |
|---|---|---|
| 10,000 gal | 1.4 lb | 635 g |
| 15,000 gal | 2.1 lb | 953 g |
| 20,000 gal | 2.8 lb | 1,271 g |
| 25,000 gal | 3.5 lb | 1,589 g |
Stabilizer to raise CYA
Per 10 ppm of cyanuric acid. Add it slowly through the skimmer on a clean sock or in a sock hung in front of a return, because it dissolves over days:
| Pool size | Stabilizer | Metric |
|---|---|---|
| 10,000 gal | 13.4 oz | 379 g |
| 15,000 gal | 20.0 oz | 568 g |
| 20,000 gal | 26.7 oz | 757 g |
| 25,000 gal | 33.4 oz | 946 g |
If CYA is already inside its target band (30 to 60 ppm on a chlorine pool, 60 to 80 ppm on a salt pool), add none: it only goes up over a season, and the fix for high CYA is water replacement.
Salt, for saltwater pools
If the pool is saltwater and the salt test reads low, dose to 3,200 ppm, the ideal for most cells:
| Pool size | Salt to go from 0 to 3,200 ppm | Metric |
|---|---|---|
| 10,000 gal | 267.8 lb | 121.5 kg |
| 15,000 gal | 401.7 lb | 182.2 kg |
| 20,000 gal | 535.6 lb | 242.9 kg |
| 25,000 gal | 669.5 lb | 303.7 kg |
If the reading is already near 3,200, you need nothing; a 15,000-gallon pool reading 2,600 ppm needs about 75.3 lb to reach 3,200. See the saltwater winterizing guide for cell-specific ranges.
What follows the label instead
- Winter algaecide: the engine has no algaecide dose. Products range widely in concentration, so follow the product label rate for your volume.
- Winterizer and sequestrant products: likewise, follow the product label. Nothing here needs a "winter kit"; the chemistry above plus a label-rate algaecide is a complete closing.
How to dose the closing chemicals, step by step
- Test FC, pH, TA, CYA (and salt if the pool has a generator) two or three days before closing.
- Balance first: acid for pH, baking soda for TA, stabilizer for CYA, using the tables above scaled to your volume. Retest after a day of mixing.
- Shock: raise free chlorine to shock level for your CYA, 16 ppm at CYA 40, with the pump running. Never mix chlorine with any other product.
- Add the label-rate algaecide, following the product label for timing relative to chlorine.
- Run the pump for several hours after each addition, then move on to the water level and the cover.
Questions people ask
Do I need a winterizing chemical kit?
Usually not. A kit is a fixed dose sold for a size range, which can over-dose a small pool. Dose your actual readings instead: chlorine to shock level, balance chemicals from the test, and an algaecide at the label rate.
How much chlorine do I add when closing?
Enough to reach shock level for your CYA: 16 ppm at CYA 40, from wherever your test reads now. That is about 2 gal of 10% liquid chlorine per 15,000 gallons when starting from FC 3.
Can I use a bag of pool shock instead?
Yes, if you dose by weight for your volume; cal-hypo adds calcium, and dichlor adds CYA with every pound. The water check doses whichever sanitizer you select and counts what it carries in with it.
Should I add algaecide when I close?
If you use one, follow the label rate for your pool's volume. It is insurance, not a requirement: a balanced, shocked pool closed cold and covered usually opens clear without it.
Do I add all the chemicals at once?
No. Balance and retest first, then shock, then the algaecide at its label's timing relative to chlorine. Chlorine and acid never go in together or mix anywhere, including in a bucket.
Next step
For your own pool, the water check turns your readings into exact doses, and the closing walkthrough puts the chemicals in order.