Guide
How to close a pool for winter, step by step
Close an inground pool for winter in one afternoon: balance the water to target, shock to 16 ppm at CYA 40, drop the level, blow the lines, and cover it. Doses for a 15,000-gallon pool included.
Updated · 6 min read
Close your pool once the water holds below 65°F (18°C) for most of the week, usually October or November. Balance the water, raise free chlorine to 16 ppm at CYA 40, drop the level, blow the lines and cover it. For a 15,000-gallon pool starting at FC 3, that shock is about 2 gal of 10% liquid chlorine.
Balancing before you cover is the step that decides whether the water comes back clear in spring. Everything after it is plumbing and a tarp. One worked example runs through this guide: a 15,000-gallon plaster pool with a sand filter, closing in November, dosed with 10% liquid chlorine.
How to close a pool, step by step
- Test the water and balance it two to three days before closing day.
- Shock the pool to shock level for your CYA, with the pump running.
- Add a winter algaecide at the product label rate, following the label for timing relative to chlorine.
- Lower the water level for your cover type.
- Turn off the breaker and drain the pump, filter, heater and chlorinator at their plugs.
- Blow the lines with a shop vac and plug the returns.
- Set the cover and tighten the straps.
- Keep the cover pumped off all winter and check it after windstorms.
Each step is detailed in the sections below.
When to close
Watch the water temperature, not the calendar. Algae and bacteria slow down as water cools, so a pool closed while the water is still warm spends its chlorine fast and can turn green under the cover. Wait until the water holds below about 65°F (18°C) for most of the week. This is a rule of thumb, not a chemistry figure: the engine has no cold-water dose modifier, and closing date varies by weeks across regions. In the far north that is September; in the Sun Belt many owners run the pool all year and never close at all.
Close before the first hard freeze, not the first frost. The app's winter watch sends a first-frost alert at a 35°F overnight low, which is a good deadline to work back from.
Balance the water a few days ahead
Test and adjust two to three days before closing, so each chemical has time to mix and you can retest. These targets come straight from the app's water check, and they are the same targets the pool has all year: there is no separate winter target set.
| Reading | Target (plaster, liquid chlorine, CYA 40) |
|---|---|
| Free chlorine | 5 to 7 ppm, never below 3 |
| pH | 7.2 to 7.8, aim for 7.6 |
| Total alkalinity | 60 to 80 ppm, aim for 70 |
| Calcium hardness | 250 to 650 ppm, aim for 350 |
| Cyanuric acid | 30 to 60 ppm, aim for 40 |
For the example pool at pH 7.8 and TA 80, bringing pH back to 7.5 takes about 11.9 fl oz of 31.45% muriatic acid (353 mL). Raising TA by 10 ppm takes about 2.1 lb of baking soda (953 g), and raising CYA by 10 ppm takes about 20.0 oz of stabilizer (568 g) in this 15,000-gallon pool. The water check computes the dose for your own readings and volume.
Shock before you cover
Raise free chlorine to shock level and let it run for a few hours with the pump on, so the water goes under the cover with no algae seed left. Shock level depends on CYA, because CYA holds chlorine back.
At CYA 40, shock level is 16 ppm. From FC 3, that is 13 ppm × 15,000 gal ÷ 781.8 = 249.4 fl oz of 10% liquid chlorine, about 2 gal (7.5 L). Add it with the pump running, brush, and let the filter run several hours before moving on.
If you use mustard-algae rates, the figure at CYA 40 is 24 ppm. That is about 1.6 times the dose above; the water check gives the exact amount.
The winter kit chemicals
Besides chlorine, two additions are common at closing, and neither is an engine figure:
- Winter algaecide: add one dose following the product label rate. The engine has no algaecide dose; label rates differ by product and concentration, so follow the label rather than any table.
- Stain and scale sequestrant (plaster pools): if you use one, follow the product label. Cold water makes the saturation index drift corrosive, which is a plaster risk; the chemistry guide below explains it.
Lower the water level
General guidance, and it depends on your cover; the app's closing checklist carries the same figures. Solid winter cover: drain 4 to 6 inches below the skimmer. Mesh safety cover: drain 12 to 18 inches below the tile line or coping, because rain and snowmelt pass through a mesh cover and the level has to absorb a winter's precipitation. Vinyl liner pools: never drain below the shallow-end floor; an empty vinyl liner shrinks and cracks. Leave the pump off while you drain unless you are vacuuming, and never fully drain the pool: groundwater pressure on an empty shell can lift or crack it.
Drain equipment and blow the lines
Any water left in plumbing or equipment can freeze, expand and split it. General guidance, from the app's closing checklist:
- Turn the breaker off and the timeclock to off.
- Drain the pump, filter, heater and chlorinator at their drain plugs, and leave the plugs out or store them in the pump basket so you find them at opening.
- Blow the lines with a shop vac or blower and plug the returns; lines you cannot blow out need pool antifreeze following the product label.
- Open any above-water equipment lids so trapped water can escape.
Cover and leave it
Set the cover, tighten the straps on a safety cover, and keep it clean of standing water all winter; a cover pump or a siphon handles the puddles. Cover care is a cadence, not a figure: check it after windstorms and pump off accumulated water within a day or two. Water on top of a solid cover is where most cover damage starts.
Common mistakes
- Closing too warm. Chlorine burns off in warm water and algae has a head start under the cover.
- Skipping the shock because "it's just winter". Shock level at your CYA is the floor that keeps the water from turning; below it, a green opening is common.
- Draining too far. Below the shallow floor in a liner pool the liner shrinks; in a plaster pool groundwater can lift the shell.
- Leaving water in the heater. A split heat-exchanger coil is the most expensive freeze failure there is.
- Covering with leaves in the water. Leaves stain plaster and feed algae all winter. Skim first.
Questions people ask
When should I close my pool?
When the water holds below about 65°F (18°C) for most of the week, before the first hard freeze. That is early fall in the north and late fall in the mid-Atlantic; in the warmest regions pools often stay open all year. Watch the app's first-frost alert at a 35°F overnight low as your deadline.
What chemicals do I need to close a pool?
Chlorine to shock level for your CYA, a winter algaecide at the label rate, and balance chemicals as your test calls for: acid for high pH, baking soda for low alkalinity, stabilizer for low CYA. The chemicals guide below lists doses by pool size.
How far down do I drain my pool for winter?
4 to 6 inches below the skimmer under a solid cover, or 12 to 18 inches below the coping under a mesh safety cover. This is general guidance that follows your cover type, not a chemistry figure, and a vinyl liner pool should never be drained near the floor.
Do I really need to blow out the lines?
Yes, if you freeze. Water left in a line or a heater expands when it freezes and splits the pipe or the coil. Blow them out and plug them, or use pool antifreeze in lines you cannot reach.
Can I close a green pool?
Get it blue first. Shock to the level your CYA calls for and filter until it clears, then close. A pool closed green stays green, and spring cleanup costs more than the few days this takes.
Next step
Enter your readings in the water check for the exact balance and shock doses for your pool, and see what chemicals to use and how much for the dose table by pool size.