Guide
How to winterize a saltwater pool
Winterizing a saltwater pool: salt levels from the engine's cell table, the salt dose for your volume, SWG balance targets, and the cell-temperature cutoff that is manufacturer guidance, around 60F water.
Updated · 6 min read
A saltwater pool closes like any other, with two salt-specific jobs: check the salt level against your cell's range (most aim for 3,200 ppm within 2,700 to 3,600 ppm) and switch the cell off for the season. Its low-temperature cutoff is around 60°F water: that figure comes from your cell manual, not from chemistry.
Everything chemistry in this guide comes from the app's engine; everything about the cell itself comes from manufacturer guidance, and your cell manual wins wherever they differ.
How to winterize a saltwater pool, step by step
- Test salt, CYA and the rest of the water two to three days before closing day.
- Top up salt to your cell's ideal if the reading is under range, at least a day before covering.
- Balance to the salt-pool targets, aiming for pH 7.5 and CYA 70.
- Shock the pool to shock level for your CYA, with the pump running.
- Switch the cell to off at the unit, not just the timeclock.
- Inspect and, if needed, clean the cell plates per the manual.
- Drain, blow out and plug the equipment and lines with the rest of the pool, and cover it.
Each step is detailed below.
Salt level: where it should be
The engine's default salt band is 2,700 to 3,600 ppm, aiming for 3,200 ppm, and above 4,000 ppm is risky for the cell and the water. Cells have their own ranges, and they differ more than most owners expect:
| Cell | Range (ppm) | Ideal (ppm) |
|---|---|---|
| Hayward AquaRite / TurboCell | 2,700 to 3,400 | 3,200 |
| Pentair IntelliChlor | 2,800 to 4,500 | 3,600 |
| Jandy AquaPure | 3,000 to 3,500 | 3,200 |
| Jandy TruClear | 3,000 to 3,500 | 3,000 |
| CircuPool | 3,000 to 4,000 | 3,500 |
| Solaxx Reliant | 3,000 to 4,000 | 3,500 |
| Unknown cell | 2,700 to 3,600 | 3,200 |
Test salt with a proper test (strip, titration or the cell's own reading) before adding anything. Cell manuals commonly note that cold water reads low on the cell's own sensor, so a low reading in a cold pool may not mean low salt; that is manufacturer guidance, not an engine figure, so dose by a test you trust.
The salt dose, if you need one
From 0 (a fresh fill) to 3,200 ppm:
- 10,000 gal: about 267.8 lb (121.5 kg) of salt
- 15,000 gal: about 401.7 lb (182.2 kg), roughly ten 40-lb bags
- 20,000 gal: about 535.6 lb (242.9 kg)
- 25,000 gal: about 669.5 lb (303.7 kg)
- 50,000 L: about 160 kg (353.7 lb)
Top-ups are much smaller: raising a 15,000-gallon pool from 2,600 to 3,200 ppm takes about 75.3 lb (34.2 kg), and a 50,000-liter pool from 2,600 to 3,200 ppm takes about 30 kg. Use ordinary pool salt or water-softener salt (sodium chloride, no additives); the salt calculator computes your exact dose.
Add salt with the pump running, brush to help it dissolve, and give it a few hours before retesting. Do not add salt on closing day itself: dose it at least a day ahead so it is fully mixed before the cover goes on.
SWG balance targets before closing
Salt pools run different targets from liquid-chlorine pools, because the cell needs CYA to protect its output and holds pH differently. At CYA 70, the engine targets for a salt pool are:
| Reading | Target (SWG pool, CYA 70) |
|---|---|
| Free chlorine | 5 to 10 ppm |
| pH | 7.2 to 7.8, aim for 7.5 |
| Total alkalinity | 60 to 80 ppm |
| Cyanuric acid | 60 to 80 ppm, aim for 70 |
| Calcium hardness | 250 to 650 ppm, aim for 350 (plaster) |
| Salt | 2,700 to 3,600 ppm, aim for 3,200 |
Shock before closing works the same as any pool: raise free chlorine to shock level for your CYA, 28 ppm at CYA 70 on a salt pool. That is the chart's shock level; your cover and liner may call for less. The water check computes the dose from your readings, and the chemistry before closing guide explains why none of these targets change for winter.
The cell: off for the season
Manufacturer guidance, not an engine figure: most manufacturers publish a minimum water temperature for generation, commonly around 60°F, below which the cell should be off or will shut itself down. Check your cell manual for the exact figure and whether the unit self-stops. While you are at the equipment:
- Switch the SWG to off (or its winter setting) at the unit, not just the timeclock, so it does not restart on a warm afternoon.
- Inspect the cell plates; clean now if scaling is starting, following the manual's cleaning procedure, so it is ready at opening.
- In freezing climates, the cell and its plumbing are drained and blown out with the rest of the equipment; a cell full of water can crack in a freeze.
- Some owners remove the cell and store it indoors for winter; that is a manual question too, since flow switches and unions vary.
Pump hours drop through winter in any climate; the turnover table in the pump guide is the base, and in a closed, saltwater pool the cell is simply off until opening.
Common mistakes
- Adding salt on a cold, untested reading. Dose from a test you trust, not the cell's cold-water display.
- Leaving the SWG on auto. A warm spell restarts the cell under a covered pool, so it keeps making chlorine against a cover for nothing.
- Winterizing with CYA at summer-tablet level. If the pool ran on trichlor before the cell was installed, CYA may be far above the 60 to 80 ppm salt-pool band; that is a spring problem to fix, and the CYA guide covers the drain-fraction math.
- Skipping the shock because the cell kept the pool clear. Closing shock level for your CYA is what holds the water over winter.
Questions people ask
Do I turn off my salt cell in winter?
Yes. Manufacturers set cutoffs around 60°F water temperature; the exact figure and whether the cell stops itself are in your cell manual. In freezing climates the cell is also drained with the equipment.
What salt level should my pool be at for winter?
The same level as summer: your cell's ideal, most commonly 3,200 ppm within the engine's 2,700 to 3,600 band. Targets do not change seasonally; only test it and top up if it is under range.
Do salt pools need different closing chemicals?
No: shock to shock level for your CYA and balance to the salt-pool targets, which differ mainly in CYA (60 to 80 ppm) and pH aim (7.5). The doses come from the same engine as any pool; see the closing chemicals guide.
Can I leave my saltwater pool open all winter?
In a warm climate, yes: keep the pump and cell on their reduced winter schedule and test monthly. Where water approaches freezing, close it; running a pump through a hard freeze is not a plan you can leave alone.
How much salt do I add before closing?
Only what the test calls for: the difference between your reading and your cell's ideal. A 15,000-gallon pool rising from 2,600 to 3,200 ppm takes about 75.3 lb, roughly two 40-lb bags; the salt calculator gives yours exactly.
Next step
Test salt and CYA, then enter your readings in the water check for the closing doses at the salt-pool targets, and the salt calculator if the level needs topping up.