Skip to content

Guide

What pool chemistry should be before closing for winter

Closing chemistry targets for plaster, vinyl, fiberglass and saltwater pools, straight from the app's engine: FC, pH, TA, CH and CYA. Targets do not change seasonally; cold water only shifts the saturation index.

Updated · 4 min read

Balance to the same targets your pool has all year: free chlorine 5 to 7 ppm at CYA 40, pH 7.2 to 7.8 aiming for 7.6, TA 60 to 80 ppm, and CYA 30 to 60 ppm on a plaster pool. There is no separate winter target set; cold water only shifts the saturation index corrosive.

Test a few days before closing so every addition has time to mix and you can retest before the cover goes on. The table below is what the app's water check targets, per pool type.

Closing targets by pool type

Reading Plaster, liquid chlorine Saltwater (SWG, CYA 70)
Free chlorine 5 to 7 ppm, never below 3 5 to 10 ppm
pH 7.2 to 7.8, aim for 7.6 7.2 to 7.8, aim for 7.5
Total alkalinity 60 to 80 ppm, aim for 70 60 to 80 ppm
Calcium hardness 250 to 650 ppm, aim for 350 250 to 650 ppm, aim for 350
Cyanuric acid 30 to 60 ppm, aim for 40 60 to 80 ppm, aim for 70
Salt not applicable 2,700 to 3,600 ppm, aim for 3,200

For vinyl or fiberglass, calcium hardness is a ceiling rather than a target: up to 550 ppm on vinyl, and no need to add any. CYA bands move with the sanitizer: liquid chlorine or tablets run 30 to 60 ppm, and salt pools run 60 to 80 ppm because the cell needs the protection.

Targets do not change for winter

It is worth saying plainly: the app's targets are not seasonal. The same pool has the same FC, pH, TA, CH and CYA targets in November as in July, because these ranges exist to protect the water and the surface, not to match the weather. The app uses the same targets all year; the engine has no cold-water target set. Here is what actually changes with cold water.

Two things, and neither is a target:

  • Chlorine demand falls. Algae and bacteria slow in cold water, so chlorine lasts longer. The engine has no cold-water dose modifier, but the practical effect is that a pool closed at shock level holds longer than one closed in July heat.
  • The saturation index drifts corrosive. That is the next section.

Cold water pushes the saturation index corrosive

The saturation index (CSI) says whether your water is scale-forming or corrosive. Temperature is one of its inputs, and cold water reads lower: the same water that is balanced at 80°F reads corrosive at 50°F. The engine computes it directly.

Take water at pH 7.5, TA 70, CH 350, CYA 50 with 1,000 ppm salt. The engine reads it at −0.18 at 80°F, −0.46 at 50°F and −0.56 at 40°F. Balanced in autumn, corrosive by mid-winter, on paper.

On plaster that matters: corrosive water dissolves plaster over months. The counterweight is calcium hardness, which is why the closing routine balances CH to 250 to 650 ppm before the cover goes on. Vinyl and fiberglass get a wider band from the same engine, −0.6 to +0.6 against plaster's −0.3 to +0.3, so this is mostly a plaster and pebble concern. If you want to see your own number, the CSI guide explains the scale and the water check computes it at your temperature.

How to get the water closing-ready, step by step

  1. Test FC, pH, TA, CH, CYA (and salt on a saltwater pool) two or three days before closing day.
  2. Adjust TA with baking soda or acid first, because TA holds pH in place.
  3. Bring pH to the middle of the range, 7.6 on liquid chlorine, 7.5 on a salt pool.
  4. Bring calcium hardness into range; on plaster this is the winter-scale insurance.
  5. Set CYA where it belongs and shock to shock level for that CYA (16 ppm at CYA 40), then let the pump mix everything for a day.
  6. Retest the next day, adjust anything that drifted, then close.

Questions people ask

Should pool chemistry be different for winter?

No. Targets are the same all year; the engine has no winter target set. What changes is behavior: chlorine lasts longer in cold water, and the saturation index reads more corrosive as temperature drops.

What should free chlorine be when closing?

After the final shock, at shock level for your CYA: 16 ppm at CYA 40. The everyday target around it is 5 to 7 ppm, never below 3, on a liquid-chlorine pool at CYA 40.

Does cold water need more calcium?

Cold water reads more corrosive on the saturation index, and calcium hardness is the lever that offsets that on plaster. Bring CH to 250 to 650 ppm before closing; that target is the same all year, but it does the most work in the coldest months.

Do I test under the cover during winter?

Monthly in mild-winter regions where the water stays liquid and warm enough for algae, per the app's winter reminders. Under ice or a frozen cover in a freezing climate, there is nothing to test until thaw.

Next step

Enter your closing-day readings in the water check; it shows each target and the exact dose to reach it. The closing chemicals guide lists the doses by pool size.