Skip to content

Guide

What to check before buying a house with a pool

The buyer's checklist: the pool-specific inspection, what to run and watch at the walkthrough, water test targets, leak and crack signs, drain covers and permits, and the running-cost math.

Updated · 8 min read

Make your offer conditional on a pool-specific inspection; a standard home inspection does not cover the pool. At the walkthrough, run the equipment, look for leaks and penny-wide cracks, test the water, and measure the volume: a 32 ft by 16 ft pool holds about 17,200 gallons and aims for 5 to 7 ppm of free chlorine.

A pool is one of the largest machines on a property, and its age is not visible from the curb. The walkthrough is where you find out what the house will cost on top of the mortgage, and the inspection period is where you get the money back if the numbers are bad. Here is what to check, in the order that matters.

The inspection a standard one misses

A standard home inspection does not typically include the pool. The American Society of Home Inspectors publishes a separate set of auxiliary standards of practice for residential pool and spa inspections (ASHI), which marks it as its own specialty, and a pool inspector or service company will cover the shell, coping, deck, visible plumbing and equipment. A standalone pool inspection averages $125 to $250 (NAR). Put it in your offer as a condition, alongside the home inspection. If the seller refuses to let one happen, treat that as an answer.

What to do at the walkthrough

Ask the seller to run it. Pump, filter, heater, lights, cleaner. Listen to it: high-pitched sounds or a struggling motor mean the equipment is telling you something. If the pool is covered or closed for the season, ask for last summer's photos and a straight answer about whether the equipment ran all season.

Read the equipment pad. Note the make, model and age of the pump, filter, heater and chlorinator, and ask for receipts. Pool equipment has a known service life and is expensive to replace all at once; a ten-year-old heater or a twelve-year-old pump is a pool with bills due (Home & Porch). Check the filter for rust and cracks, and the ground around the pad for leaks. A variable-speed pump is a plus: it lets the owner run the turnover slowly and cheaply, especially on off-peak rates.

Look at the water and the shell. Green or discolored water is a chemistry problem, usually fixable, but it is also evidence of how much the pool is used and how much it is watched. A water line that sits well below the tile, or keeps dropping, is a leak until proven otherwise. On the surface, small "hydration" spider cracks are usually superficial; the crack that matters is a separation crack you could fit a penny into (NAR). Loose tile, missing grout, a shifting deck and a coping-to-deck joint that was never sealed all let water behind the surface.

Leaks: the bucket test

Ask for water bills across a full season, then separate evaporation from a leak with the bucket test during your inspection period: set a bucket on a pool step, fill it to the pool's water level, and mark the level inside the bucket and outside on the wall. Twenty-four hours later, evaporation takes a little off both; if the pool level dropped noticeably more than the bucket's, the pool is losing water somewhere. A high water bill (Home & Porch), soggy soil by the equipment pad (Backbay Pools) and a steadily falling line all point the same way. A surface hairline crack can be fixed for about $10 in epoxy; a real structural or plumbing leak costs thousands (NAR).

Measure the volume and test the water

The first number to get is volume, because every chemical, filter load and resurfacing quote scales with it. A 32 ft by 16 ft pool, 3.5 ft deep at the shallow end and 5.5 ft at the deep end, holds about 17,200 gallons (about 65,200 liters): surface area times average depth, with one cubic foot of water being 7.48 US gallons. In metric, the same pool is 10 m by 5 m, 1.0 to 1.8 m deep, and holds 70,000 liters (about 18,500 US gallons). The pool volume calculator does it for any shape.

Then test the water with a kit and compare it to what it should be. At a stabilizer (CYA) of 40 ppm, the targets are:

Check Target at CYA 40
Free chlorine 5 to 7 ppm, never below 3
pH 7.2 to 7.8, aim for 7.6
Total alkalinity 60 to 80 ppm, aim for 70
Calcium hardness 250 to 650 ppm, aim for 350
Cyanuric acid (CYA) 30 to 60 ppm, aim for 40

Water that sits far out of these bands tells you the pool was neglected. If it is green, the fix is a shock: at CYA 40, shock level is 16 ppm, and in the 17,200-gallon example pool, starting at 3 ppm, that is 2¼ gal (8.5 L) of 10% liquid chlorine. The green pool guide walks through it, and Pool CSI and LSI explained covers what out-of-balance water does to the surface. If the pool has a salt system, the salt cell has a limited life: ask when it was last changed, and the salt guide gives the target levels. For routine doses, 12.8 fl oz of 10% liquid chlorine per 10,000 US gallons raises free chlorine by 1 ppm (100 mL per 10,000 liters).

Safety and paperwork

Drain covers. Under the Virginia Graeme Baker Pool and Spa Safety Act, every pool or spa drain cover made or sold in the US must meet the anti-entrapment standard, ANSI/APSP/ICC-16 (2017) (CPSC, eCFR). An old flat grate over a single main drain is worth a professional opinion before you close (Home & Porch).

Barrier. Local code sets the fence height and gate rules. Florida Statute 515.29, for example, sets a 4-foot minimum in many situations; check your own code and measure the barrier at several points, looking at gates, latches and whether the house itself forms part of the enclosure (Backbay Pools).

Permits. An unpermitted pool or unpermitted electrical connection becomes your problem, not the seller's. Check the permits before you buy, and get electrical or gas work on the pool verified by a licensed pro. Verifying a gas heater's connection, venting or any wiring in the equipment pad is a licensed professional's job, not a buyer's.

Records. Ask for receipts, service invoices, warranties and the date the surface was last done. When the surface was last refinished is the single biggest future bill on the property: ask why if it was done recently, and what it cost.

What it will cost to run

The pump has to push the whole pool through the filter about once a day. The 17,200-gallon example pool on a pump moving 40 gpm needs about 7.2 hours for one turnover. Typical full-speed flows by pump size:

Pump size Typical flow at full speed
¾ HP 55 gpm
1 HP 65 gpm
1.5 HP 90 gpm
2 HP 110 gpm
2.5 HP 130 gpm
3 HP 150 gpm

On a variable-speed pump the speed choice is a money choice. Example: the 17,200-gallon pool on a 1.5 HP variable-speed pump that draws 1,500 W at full speed, with electricity at $0.25 per kWh.

Speed Hours a day Power Energy a day Cost a month
3,450 RPM (full) 3.2 h 1,500 W 4.8 kWh $36.00
1,500 RPM 7.4 h 123 W 0.91 kWh $6.84

Same turnover, 81% less electricity at the low speed, and in a week with a high of 85°F or more the low run grows to 9.2 hours, about 25% more time. The pump run-time planner works it out for your pool and your rate. Add routine maintenance, which commonly runs $1,000 to $4,000 a year (NAR), and you have the pool's real monthly cost. The pump guide explains the turnover rule.

The buyer's walkthrough, step by step

  1. Put a pool-specific inspection in the offer, separate from the home inspection.
  2. Ask the seller to run the pump, filter, heater and lights, and listen to them.
  3. Check the water line, the color of the water, the tile, the cracks and the coping joint.
  4. Read the equipment labels: make, model and age of pump, filter, heater and chlorinator.
  5. Measure the water surface and depths and work out the volume.
  6. Test the water and compare it to the targets above.
  7. Run the bucket test for leaks during the inspection period.
  8. Ask for receipts, service records, permits and the last surface date.

Questions buyers ask

Should I pay for a separate pool inspection?

Yes. The standard home inspection does not typically cover the pool, and a pool-specific one averages $125 to $250. It costs less than any of the things it is built to find.

What if the pool is covered or closed when I view it?

Ask for last summer's photos and a straight answer about how the equipment ran all season, and make the offer conditional on seeing the pool running and inspected. Assume nothing until you have seen it.

Is green water a dealbreaker?

Usually not. It is a chemistry fix: at CYA 40, shock level is 16 ppm, and in the 17,200-gallon example pool that is 2¼ gal (8.5 L) of 10% liquid chlorine from a free chlorine of 3. What matters more is why the water went green: how often the pump ran, and whether anyone was checking it.

What if the equipment is old?

Budget the replacement as part of the deal, and consider a variable-speed pump in the swap. In the example above, the same turnover at the low speed costs $6.84 a month instead of $36.00, about 81% less.

Can I negotiate over what the inspection finds?

Yes, while you are still in the inspection period. Put the inspector's written findings and repair quotes in front of the seller and ask for the repairs, a credit or a lower price. A seller's "it's in good condition" is not a record; the report is.